Also see Independent Samples T-Test - Quick Introduction.

## Null Hypothesis

The **null hypothesis** for an independent samples t test is that
two populations have equal means on some metric variable.

For example, do men spend the same amount of money on clothing as women? We can't reasonably ask the entire *population* of men and women how much they spend. So we'll draw a *sample* of men and women. These **samples are independent** because they don't overlap: everybody is either man or woman, never both.

Now, **sample outcomes tend to differ** a bit from population figures. So if the average amount spent is precisely equal for *all* men and women, we'll probably still see *slightly* different means between our samples. However, *very* different sample means suggest that the population means weren't equal after all. A t test tells us if a **sample difference is big enough** to draw this conclusion.

## SPSS Independent T Test Example

A scientist wants to know if children from divorced parents score differently on some psychological tests than children from non divorced parents. The data collected are in divorced.sav, part of which is shown below.

The last 4 variables in our data file hold our test scores. For each variable, we'll use a t test to evaluate if the mean scores are different between our 2 groups of children.

## Independent Samples T Test - Assumptions

Conclusions from an independent samples t test can be trusted if the following assumptions are met:

**Independent observations**. This often holds if each case in SPSS represents a different person or other statistical unit. This seems to hold for our data.**Normality**: the dependent variable must follow a normal distribution in the population. This is only needed for samples smaller than some 25 units. We'll see the actual samples sizes used for our t test after running it so we won't bother about normality until then.**Homogeneity**: the standard deviation of our dependent variable must be equal in both populations. We only need this assumption if our sample sizes are (sharply) unequal.

SPSS tests if this holds when we run our t test. If it doesn't, we can still report corrected test results.

If these assumptions are badly violated, you could consider using a Mann-Whitney test instead of a t test. This is suitable for ordinal variables as well.

## Quick Data Check

The **data at hand have been prepared** and are good to go. However, if you run a t test on other data, you should at least inspect some histograms of your dependent variable(s). Make sure their distributions look plausible. If they contain any extreme values, specify them as user missing values.

## Running an Independent Samples T Test in SPSS

Running an independent samples t test in SPSS is pretty straightforward. The screenshots below walk you through.

We'll first test anxi and make sure we understand the output. We'll get to the other 3 dependent variables later.

Clicking creates the syntax below. Let's run it.

## SPSS Independent Samples T Test Syntax

***Independent-samples t-test syntax for anxi by divorced.**

T-TEST GROUPS=divorced(0 1)

/MISSING=ANALYSIS

/VARIABLES=anxi

/CRITERIA=CI(.95).

## SPSS Output for an Independent Samples T Test

We first take a look at **Group Statistics**. First off, note that there's only a small difference between our sample means. Children from divorced parents have an average anxiety score of 22.8 whereas the other children score 21.5.

Second, note that the **sample sizes** used for our t test are 49 and 34. Since both are larger than 25, we don't need to bother about the **normality assumption**.

If you encounter smaller sample sizes while analyzing other data, you may check for normality by inspecting histograms or running a Kolmogorov-Smirnov test.We don't recommend this test because it has low power in small samples. Since it still seems to convince a lot of people, you may consider using it anyway.

## Independent Samples T Test Output

Note that we have two lines of t test results: equal variances assumed and equal variances not assumed. So which line should we report? Well, this depends on **Levene's test for equal variances** which tests the aforementioned homogeneity assumption.

As a rule of thumb, if **Sig. > 0.05**, we conclude that the assumption of **equal variances holds**. Since Sig. = 0.159 here, we report the first line of t test results, denoted as equal variances assumed.

If **Sig. (2-tailed) > 0.05**, we usually conclude that our **population means are equal**. “Sig.” is called a significance level (or just “p”) in reports. P indicates how likely our *sample* result is if our *population* means are really equal. In our case, p = 0.055 (a 5.5% probability) and that's not unlikely enough for rejecting our null hypothesis.

**df** (degrees of freedom) is not really interesting but we'll report it anyway. The same goes for **t**, our test statistic.

## What About the Other Variables?

Right, let's now analyze all 4 test scores. We can do so by reopening the t test dialog from the menu (tip: try the **dialog recall** tool here). Alternatively, just add the variable names to the previously used syntax.

***Independent-samples t-test syntax for anxi by divorced.**

T-TEST GROUPS=divorced(0 1)

/MISSING=ANALYSIS

/VARIABLES=anxi depr comp anti

/CRITERIA=CI(.95).

## Result

At this point you should be able to draw the right conclusions. The null hypothesis of **equal population means** is rejected only for our last two variables: compulsive behavior, t(81) = -3.16, p = 0.002 and antisocial behavior, t(51) = -8.79, p = 0.000.

The figure below shows how we **first** inspect Sig. for **Levene's test** and **then** choose which **t test** results we report.

## Reporting an Independent Samples T Test

First off, report **means and standard deviations** for both groups. Perhaps include sample sizes as well: for multiple tests, these may vary due to missing values. I like reporting such descriptive statistics in a simple overview table as shown below.

You *could* add some columns to this table holding **df**, **t** and **p** for each test (p is denoted as “Sig. (2-tailed)” in SPSS).

Alternatively, report each t test result as
“Children from divorced parents scored higher on compulsive behavior than other children, t(81) = -3.16, p = 0.002.”

Thanks for reading!

## This tutorial has 62 comments

## By liz on November 4th, 2016

very helpful. Thank you

## By Ruben Geert van den Berg on August 27th, 2016

Thanks!

## By nisreen on August 27th, 2016

nice tutorial

## By Vicki Tang on August 13th, 2016

It is very informative and it really helps me to interpret especially the Levene's test

## By Uzochukwu Ifeanyi on July 23rd, 2016

Thank you so much for this, it was very helpful.